Ubuntu mount samba share12/7/2023 ![]() Output: Next, add the following details at the end of the file: Your machineâs IP address. If I mount the shares from the command line (command below) it is mounted just fine. I can access the SMB shares on my Windows computer but on my Ubuntu 18.04 computer I can't get the shares mounted in fstab. Open this file using the text editor of your choice. I just upgraded my file server from 16.04 to 20.04 and everything seems to be working except for my SMB mounts on my Ubuntu computer. Sep 12 21:01:05 containers2 systemd: Failed to mount /mnt/smb. Alternatively, you can also mount SMB shares manually by configuring the /etc/fstab file. Sep 12 21:01:05 containers2 systemd: mnt-smb.mount: Failed with result 'exit-code'. Sep 12 21:01:05 containers2 systemd: mnt-smb.mount: Mount process exited, code=exited, status=32/n/a here's what's on /var/log/syslog: Sep 12 21:01:05 containers2 systemd: Mounting /mnt/smb. It's when the Raspberry Pi is rebooted/started is when it failed to mount. Whe I run sudo mount -a, it mounts successfully. I hope someone can show me the way out of this darkness. ![]() LABEL=system-boot /boot/firmware vfat defaults 0 1 ![]() To export /data/shared you have to add the following at the end of the file: data comment shared path /data/shared guest ok. On RaspPi: LABEL=writable / ext4 defaults 0 1 To allow everyone from the group SAMBASHARE to access the shares add the following to the global directive: create mode 664 workgroup SAMBASHARE security user usershare allow guests yes. It appears /etc/fstab is different too between the two platforms. Use vers3.0 as minimum and if doesnât work, specify secntlmv2 Itâs another common issue that some people use secntlm instead of secntlmv2. Lets take just the first share as an example - and here Im correcting the read-only yes line: Fr-data path /free/fr/data read only yes valid users global write list borhacker force create mode 0775 force directory mode 0775 create mask 0775 directory mask 0775. This version of SMB protocol is deprecated, unefficient and gives you a very bad performance. I can get the drive to mount manually by using: sudo mount -t cifs //192.168.2. 192.168.1.5/Media /mnt/smb cifs guest,_netdev,uid=ronny 0 0 If you mount shares from a modern version of Windows, do not use vers1.0. I am a little confused on the proper fstab entry for a samba share in Ubuntu 12.04. But it fails to mount in Raspberry Pi based Ubuntu 20.04. The following works well in all x86-based Ubuntu 20.04. Im trying to automatically mount a samba share residing on nas running openmediavault 5.6.12-1 and samba version 4.9.5-Debian on my desktop running Ubuntu 20.04.3. There is some good information Here on adding credentials via txt file and securing but as this is my home environment i donât need that.I have been trying very hard to mount a samba share. If this comes back with no errors, the share should mount after each reboot. A mount point is the location where two file systems are joined: in this case, your local file system and the remote Samba file system. 192/168.16.31/software /mnt/sw cifs username=admin,password=password,iocharset=utf8,sec=ntlm To mount the Samba share, you can create a new directory that will act as the mount point for the share. Set a Samba password for the user: sudo smbpasswd -a .Sec=ntlm allows ntlm authentication which i have on my SMB SharesĪt the end of my fstab I entered the following: I had a fresh install of 20.04, and it took me these two steps to get the sharing working with Ubuntu 18: Configure the workgroups protocol at /etc/samba/smb.conf (here SMB3 wouldnt work): client min protocol CORE server min protocol CORE. Iocharset=utf8 allows access to files with names in non-English languages. The synatx is as follows: //servername/sharename /media/windowsshare cifs username=, password=,iocharset=utf8,sec=ntlm Change the permissions on the file for security: sudo chmod 0400 /etc/samba/user permissions of 0400 read only. directory mask 0700 By default, serverusername shares can be connected to by anyone with access to the samba server. Now we need to add this mapping into the fstab with grouprw permissions, set next parameter to 0775. In my case I am creating a Directory called sw in /mnt Next we need to create a Directory on the Ubuntu machine to Mount the Share to. The Share in question was a Software repository on my NAS and so in my instructions you will see software or sw referenced, these you will have to change with your equivalent. I have a few SMB Shares running in my Home which i wanted to access from one of my Ubuntu Desktops.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |